Buy TKO Heavy Bag Wall MountTKO Heavy Bag Wall Mount Product Description:
- Heavy bag wall mount will attach to any standard wall, bringing an intense boxing workout to the comfort of your own home
- Holes are lined up to allow you to screw directly into 16-inch, on-center wall studs
- Convenient pull-pin adjustment to swivel bag to the side and out of the way when not in use
- Arm extends 27 inches away from the wall
- Mount holds up to a 100-pound bag (sold separately)
Product Description
TKO's heavy bag wall mount will attach to any standard wall. The holes are lined up to allow you to screw directly to 16-Inch, on center wall studs. There is a convenient pull pin adjustment that allows the bag to swivel to the side when not in use. This sturdy wall mount lets you keep your heavy bag ready to go in any room in the house.
Customer Reviews
Most helpful customer reviews
46 of 48 people found the following review helpful.
Works great for what it is.
By C. H.
This mount works great for what it is. Please be aware that for $70 you are not going to get super strength or sealed ball bearings. However it hangs my 100lb heavy bag and tolerates my punching and kicking just fine, and when I need the space it swings the bag out of the way just as advertised. Is a good product at a good price.Mounting: I would have to seriously question the intelegence of someone that would try to mount this straight to a sheetrock wall. To stand up to a swinging 100lb bag is going to require some re-enforcement. Get a four foot 2x10 from your local lumber store and cut two 20 inch long pieces. Position the supports so that the TKO (top and bottom) brackets will be centered on the wood. This means the outside holes will line up verticly between the screws that mount the wood to the wall. Mount these supports to the wall studs with four 3/8" x 4" lag screws and washers per board. You should have about 2" of wood extended beyond the wall studs and screws for strength. Mount the TKO with 3/8" x 4" lag screws in the outside holes and 3/8" x 2" lag screws (and washers) in the inside holes. You will want to pre-drill all these holes so you are not splitting the wood. This is how I did it, and my TKO mount does NOT flex at all.
11 of 11 people found the following review helpful.
Nothing like it in this price range
By Joseph T. Goodman II
I have been looking for a convienient way to hang my 100lb heavy bag. This mount is very sturdy, I used concrete anchors and hung it on my basement wall. I would bet that it could hold well over 100lbs. I think that limitation is based on hanging it on normal 2x4 wall studs.Overall great product, but caution it doesn't come with bolts/screws to hang it, you have to visit your local hardware store for that stuff.Then when your all done hitting the bag you can just swing it out of the way.
10 of 11 people found the following review helpful.
Works great. Would recommend
By Jeff Bennion
This product works great. I was worried after reading some of the other reviews, but after I installed it, I no longer have any concerns. First of all, if you install this into studs and it rips out of the wall, you either didn't install it into studs, or you have bad wood. Either way, it's not the fault of this product. I was lucky because I put it in my garage and the studs are exposed, but a simple $8 stud finder from the store should help you put it in the right place. I also put some 4x4 between the studs going horizontally behind the two bars for added support, but I didn't really feel that this was necessary. I also liked how it locked into place in both the storage mode and use mode using a simple spring pull pin.There were some things I didn't like though. It doesn't come with the bolts to install into the wall. You have to wait for it to arrive, then go to Home Depot and buy the proper lag bolts (I think they were 1/2 or 5/8, I don't remember. I wouldn't go smaller than 2.5 inches long). Then, you have to drill holes in the wall (make sure the holes are significantly smaller than the lag bolts, or your stand will just fall out of the wall). Then put the lag bolts in the hole. It's simple to install and fast. Secondly, I would have liked to have a third support bar above the the arm that holds the bag. The more support the better, especially when you are hanging something around 100 lbs that is going to have force tugging it in different directions. Also, I didn't like how there are extra holes that don't line up with studs. The two support bars have two holes on either side that go into studs, and then there are two more on either side of the rotating arm. These would just go into drywall or nothing and I don't think they would provide any additional support, just leave holes in your wall. Like I said, what I did was put a couple 4x4s along the back of the support bars and then I could drill some more lag bolts into the wall into my new makeshift studs, but that would only work if your studs are exposed, which in most cases, they are probably not.Bottom line, it's a great product and a great price. I would recommend it to anyone. It's certainly better than those stands. With the stands, you can't circle the bag as much, which is crucial.
See all 26 customer reviews...Latest Price:
See on Amazon.com!
More Info:
See on Amazon.com!
See Customers Review:
See on Amazon.com!
Buy TKO 502VMT Muay Thai Bag 125lbs
torx
I wouldn't buy it.
Hunter Fan
